Yank555.lu Android Stuff

yank555 wrote:Here is an idle run I started yesterday evening before going to bed, that's 7% in 19:21, which makes about 0.36% / h battery drain in standby. Device woke up with no issues, this is on

JP.

Same here.... On official 4.3. Around 0.36%/hr. Thank you so much for your kernel.



Sent from my GT-I9300 using Tapatalk

yank555 wrote:

JMS74 wrote:I'm just saying.. With default options that's what happens. Not trying to imply anything other. .

Thanks for your work

Sent from my GT-I9300 using Tapatalk

Still for me to understand, can you state clearly you compare :

Stock kernel PegasusQ with or without zram ?

With

My kernel PegasusQ with or without zram ?

Else your statment isn't helping much...

JP.

Sent from my SM-N9005 using Tapatalk

Sincerely don't know. Didn't mess with the settings so it's whatever comes by default.
Trickstermod says no but that can be wrong I guess

Sent from my GT-I9300 using Tapatalk

JMS74 wrote:Sincerely don't know. Didn't mess with the settings so it's whatever comes by default.
Trickstermod says no but that can be wrong I guess

Well full default in both cases would be :

Stock PegQ 300Mb zram
Mine PegQ (since you were talking about PegQ, default would be zzmoove) 600Mb zram

Rather strange, though...

Since all reports except yours say the opposite, e.g. stock would lag, while you say stock is flying, I'm somewhat confused

I can't say, since I made the kernel blind and never actually tested the ROJ with stock kernel myself... will try to test stock kernel to compare.

JP.

Send from my 'proudly eFused' Note 3 (n9005) running Yank555.lu v0.2-beta2 kernel.

hwjrmrm wrote:camera Fc ,what to do? thanks

wanhao wrote:Got camera error with Archi 1.7.1.

Hmm ... have you tried to just clear gallery / camera data ?

It's working just fine here, even burst mode.

JP.

Send from my 'proudly eFused' Note 3 (n9005) running Yank555.lu v0.2-beta2 kernel.

yank555 wrote:

hwjrmrm wrote:camera Fc ,what to do? thanks

wanhao wrote:Got camera error with Archi 1.7.1.

Hmm ... have you tried to just clear gallery / camera data ?

It's working just fine here, even burst mode.

JP.

Send from my 'proudly eFused' Note 3 (n9005) running Yank555.lu v0.2-beta2 kernel.

I'm getting "Camera Failed" error and I've tried that and flashing the whole thing again and it doesn't work

EDIT: Tried using instagram to take a pic and it seems like the kernel has definitely some issues with the camera department, as the app can't connect to the camera.

yank555 wrote:

hwjrmrm wrote:camera Fc ,what to do? thanks

wanhao wrote:Got camera error with Archi 1.7.1.

Hmm ... have you tried to just clear gallery / camera data ?

.

same here, installed wanamlite v7.2 and now the camera got error...@-@ ...

EDIT
tried cleaning cache of gallery and camera (and from recovery cache and dalvik)but no results...

Hi,

Does this kernel have tun module (vpn) support ?

Hi JP,

thanks a lot!

Awasome, unbelievable result in the battery drain on 4.3 stock ROM playing your new kernel. Last night, after installing the kernel, baterry drain varied between 0,4~0,8%/h (all sync off). (I don't use OC.)
With same app and settings, on CM (M1 or Nighthly) or on SleenBean (Build 2) + 1.6g-beta7 kernel the battery drain at night varied between 1,5~3,2%/h. It gave me less than 24 hours of battery life.
So, at least for now, stay on Stock ROM.
Yank's Kernel always!

mrmrmrmr wrote:Hi,

Does this kernel have tun module (vpn) support ?

Just connected to my workplace via vpn.

JP.

gieffe22 wrote:same here, installed wanamlite v7.2 and now the camera got error...@-@ ...

EDIT
tried cleaning cache of gallery and camera (and from recovery cache and dalvik)but no results...

I had read about this in Wanam thread, can't tell you much more than it's working fine on mine, WanamLite 7.2, and it seems to be working fine for many...

Someone suggested to cleanflash Wanam, boot full stock, run camera once, and then only install a different kernel. While I don't really see what that would change, why not give it a whirl ?

JP.